Welcome to Kingsway Instruments!
What you need. Where you need it
Backpacks offer a convenient method for organizing, storing and your carrying tools. Keeping all the tools you need in a single Fluke Pack30 means fewer trips back to the truck. Plus, the Fluke Pack30 gives you a more comfortable solution than traditional tool belts that put all the weight on your lower back, or ...
SureGrip™ accessories are designed to improve steadiness in slippery hands. Rubber overmolded surfaces and finger-hugging curves give the user a comfortable, reliable grip on the accessory so they can focus on making an accurate measurement.
The Fluke 2AC is the latest addition to the VoltAlert™ AC non-contact voltage tester family from Fluke and is designed to be pocket-sized and easy to use. The 2AC tests for energized circuits and defective grounds, whether it's for an electrician on the factory floor or the do-it-yourselfer around the house. The tip of the pocket-sized tester wi...
Test leads are an integral part of the complete measurement system and extend the capabilities of your digital multimeter. The Fluke TL71 Premium Test Lead Set has one pair of red and black comfort grip probes with flexible silicone-insulated, right-angle test leads. With distinctive comfort grip probes, they are heat and cold resistant with saf...
Kit includes sharp test probes, alligator clips for hands free connections and a soft carry case to protect your tester when not in use and store your accessories. 1000 V CAT III, 600 V CAT IV rated.
TP238 SureGrip™ Insulated Test Probe Set
AC285 SureGrip Large jaw alligator clips
C33 Zippered soft case
The T5 meter is NOT included (sold sepe...
Three piece insulated 10 kV large test clip set. Each lead is 3 meters in length
Red, Blue, Black
The TL224 SureGrip™ Insulated Test leads offer reinforced strain relief and includes banana jack termination for a variety of test lead configurations. SureGrip™ accessories are designed to improve steadiness in slippery hands. Rubber over molded surfaces and finger-hugging curves give the user a comfortable, reliable grip on the accessory so th...
3 Test Leads connected to Low-Leakage Probes (red, black, green)
3 Alligator Clips (red, black, green)
Maximum Jaw Opening: 26 mm (1 in.)
Replacement Test Lead Set for the Fluke 1550B MegOhmMeter
Length (Lead Only): 2.6 m (8.6 feet)
Cat II 1000 V, Cat III 600 V, 5kV DC Max (Probes)
Cat II 1000 V, Cat III 600 V, 20 amps (Alligator Clips)
Non-contact AC voltage detector and LED flashlight combined into one easy to use pen-style design. The LVD2 is a CAT IV 600 V rated non-contact detector that is suitable for commercial and industrial applications. The LVD2 includes dual sensitivity turning blue 1" to 5" (2.54 cm to 12.7 cm) from the source and red when at the source.
Give your Fluke tools the protection they deserve. You bought the best, why not protect them with Fluke cases. The C25 carrying case is a durable, zippered carrying case with padding and inside pocket, and high quality polyester exterior. It includes a convenient hand strap and carries most of Fluke’s popular digital multimeters. Our most popula...
*Discontinued - Please call for information on Amprobe ST101B and ST102B replacement options*
Quickly test sockets and confirm GFCI breakers are properly wired for protection with the ST102A.
The AC Line Splitter Model ALS-1 increases the sensitivity of clamp-on current probes and clamp-on meters. The Model ALS-1 provides temporary separation of conductors (avoiding splitting of the line) to facilitate measurement of current. Simply plug the Model ALS-1 into a connector for a safe measurement. Two clamp positions are available: X1 fo...
Accommodates powering the PEL 102 & PEL 103 from phase power. Powers from phase to neutral or phase to phase. Provides isolation between measurement and instrument power.
Range of use: Phase-to-neutral voltage: 110 to 277V AC; Phase-to-phase voltage: 110 to 480V AC
Max. input voltage: Permanent: 530Vac; Transient: 550V AC
Megger 1008-022 three-piece insulated lead set with test clips includes one red, one blue, and one black test lead for use with Megger 5KV and 10KV insulation resistance testers. Each 10 foot test lead has a test clip for hands-free connection to a conductor. Silicone insulation on the lead wires and test clips helps protect hands from shock and...
Megger replacement remote probe for use with MIT400/2 series.
Conforms to CAT IV 600V
Special 2-pin plug on instrument end
Probe with switch in handle end
Length: 4.25 ft. (1.3m)
Anyone with FlukeView Forms version 3.0 or later can receive a free software update by clicking the links and downloading the software from this site. Basic users would select the "Basic" link and users with the complete package would select the "plus Designer" link. If your present FlukeView Forms software is older than version 3.0 (less than 3...
FlukeView forms software with cable
Expand the power of the world's most rugged, accurate handheld test tools with FlukeView Forms Documenting Software
With FlukeView Forms documenting software, the logging capabilities of handheld test equipment can be used to solve tough problems
You can download the readings from meters into FlukeView Forms...
To address the increasing demands for reporting and documentation, Fluke presents FlukeView Forms documenting software.
FlukeView forms software with interface cable
Includes CD for FlukeView Forms Version 3.0, PC to meter serial cable, user manual, registration card, software license agreement
FlukeView Forms supports 45 bench meter
To address the increasing demands for reporting and documentation, Fluke presents FlukeView Forms documenting software
For more than 50 years Kingsway Instruments has been Canada’s most trusted source for test equipment sales, service, rentals and the fastest calibration turnarounds — bar none.
4319 Roper Rd.Edmonton, AB T6B 3S5